Çok eski bir web tarayıcısı kullanıyorsunuz. Bu veya diğer siteleri görüntülemekte sorunlar yaşayabilirsiniz.. Tarayıcınızı güncellemeli veya alternatif bir tarayıcı kullanmalısınız.
Huawei Mate 10 Pro BLA-L09 IMEI Repair + FRP Dosyası
Huawei Mate 10 Pro BLA-L09 IMEI Repair + FRP Dosyası
Aydar - #1
Merhabalar. Sevgili Mobil Kulüp kullanıcıları. Bugün sizlere Huawei Mate 10 Pro BLA-L09 IMEI Repair+FRP Dosyası Nasıl yapılır onu anlatacağım.
Yükleme işlemi.
1) SD Kart Veya Flash olması lazım.
2) SD Kartımızı Veya Flashımızı "exFAT" olarak Biçimlendiyoruz.
3) Yazılımı Ziptan Veya Rardan çıkarınız. "dload" Klasörü SD Kartımızı Veya Flashımıza Atıyoruz.
4) *#*#2846579*#*# Yapıp. Software Upgrade Tıklayınız. 2 Aşamada tekrar devam ediyoruz.
Cihaz kendini yeniden başlatım. Yazılım yüklemesini otomatik olarak yüklenecektir.
CHİMERA DA böyle bi hata var
Searching for manufacture port...
Automatic Manufacture Port enabling...
Testing connection...
Authenticating...
This may take a while.
Be patient! Do NOT disconnect the phone!
The device sent an invalid challenge.
Retry 2/5
The device sent an invalid challenge.
Retry 3/5
The device sent an invalid challenge.
Retry 4/5
The device sent an invalid challenge.
Retry 5/5
The device sent an invalid challenge.
Authentication with the device failed.
Finished at local time: [08.21.20 00:55:06]
WorkID: 104625754
öncelikle emeğe saygı teşekkür ediyorum ama cihazda frp var sıfırlanmış kurulumda kalmış ona nasıl yükleyeceğiz ses kısma ve açma tuşlarıyla yükleme yermi
Bu işlem baya geride kaldı yeni Güvenlikler falan filan.
Cihazı Arka kapağı sökülüp HCU veya Octoplus ile İşlem yapabilirsiniz.
gen_com - #68
test point ile yapıldı
Welcome to Octoplus Huawei Software v.1.2.2.2
To enable 'Manufacture' mode dial
- for Qualcomm and Hisilicon based models: *#*#2846579#*#*
ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
- for MTK based models: *#*#14789632#*#*
ProjectMenu > Background Settings > USB Port Settings > Debug Mode
To enable 'Fastboot' mode
1. Power off the phone. Remove SD and SIM cards
2. Press 'Vol-' and insert USB cable
3. Wait until phone enters 'Fastboot' mode
To enable 'Upgrade' mode
1. Power off the phone. Remove SD and SIM cards
2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
3. Wait until phone enters 'Upgrade mode'
Found COM ports:
1: COM1 İletişim Bağlantı Noktası
Job ID: 0000000000435940
2020-12-15 15:36:29 GMT -------------------------------------------------
Starting Reset FRP (Factory Mode)
Selected phone model: BLA-L09
Searching HUAWEI USB COM 1.0 port...
Writing bootloader KIRIN970_A8.1_V0...
Initializing remote service connection...
Writing XLOADER partition...
Writing UCE partition...
Writing FASTBOOT partition...
Bootloader Update successfully
Rebooting to fastboot mode...
Searching Fastboot devices...
Found a fastboot device: GAB7N17C05000680